SPECIAL ACRYLIC PRIMER FOR STRONG ADHERENCE
PRODUCT DESCRIPTION
An acrylic based isolation primer for water and humidity isolation, apply as an undercoat on concrete, wooden
exterior or interior surfaces.
AREAS OF USE
Concrete and surfaces
Plastered surfaces
Over brick and gas concrete
Painted surfaces
Over OSB and over EPS
XPS
ADVANTAGE OF THE SYSTEM
Penetrates into mineral structure of the surfaces such as stone, concrete, brick for protection.
Helps to bind the sandy and chalky materials the surface.
It supports the tissues of these material substructures.
It is co-adherent with any acrylic based material to overcome the swelling problems on the wall.
Used as a sealer, it reduces the water absorption of the surface.
Especially on the repaired parts of the surfaces (absorption varies on the surfaces) minimizes the color
tone dierences of the paint
APPLICATION
The surfaces must be removed from any old, loose and swelled materials. Cracks and splits on the surface must
be removed from any old, loose and swelled materials. Cracks and splits on the surface must be repaired.
Horizontally and vertically can be applied with roller or brush.It is recommended to apply a second layer, if the
surface is very absorptive. And if the temperature of the application surface is very hot due sunlight, it is recommended
to splash water on the surface before the applying the xative.
READY TO USE. DO NOT ADD ANY WATER!
ACRYLIC THERMAL ISOLATION PLASTER WITH SUPER
ELASTICITY
PRODUCT DESCRIPTION
Acrylic based decorative isolation plaster; with its unique air pockets, provides structure with heat isolation
isolation up to %30 along with 100% water isolation on exterior concrete and wooden surfaces. Elastic, light
strong with high adherence.
AREAS OF USE
Concrete and wooden surfaces
Plastered surfaces
Over brick and gas concrete
Painted surfaces
Over OSB and concrete surface
Glazed and mosaic etc. surfaces
Over EPS, XPS
APPLICATION
Any old, loose and swelled paint layers on the surface must be removed. Cracks and splits on the surface must
be repaired. Horizontal and vertical areas need to be applied with Hemp Paint Fixing Undercoat before applying
the first layer of Hemp Paint Thermal Insusation Plaster. Afrer waiting for at least 24 hours (on the undercoat dries),
a second layer of Hemp Paint Thermal Insulation Plaster should be applied with a steel trowel. No water needs to
to be added to the product. If Hemp Paint Insulation Plaster will be applied on the EPS sheets, plastic nets
need tobe placed with 160g/m² ratio over the EPS.
Then the first layer can be applied
DRYING TIME
Drying time of the plaster can vary with temperature and air canditions.
At 20°C, 2 hours for one layer application with 2-3 mm thickness
At 10°C, 5 hours for one layer application with 2-3 mm thickness
CONSUMPTION
For two layers of application, a surface of 1 m² can be covered with 3.5-4 kg plaster. 20 years of chemical life expectancy.
READY TO USE. DO NOT ADD ANY WATER!
ACRYLIC THERMAL ISOLATION PLASTER
PRODUCT DESCRIPTION
Thermo coating is a light and durable decorative coating which offers thermal insulation and limited sound
insulation together for concrete and wooden fronts. Thanks to the air voids and natural minerals in its structure,
it offers 30% heat insulation. It is not self-combustible and it dies down on it’s own when it is exposed to hot
frames. In virtue of this property, it corresponds with the description of ‘Fire Retardant Coating’. Jatketing done
with polystyrene foam do not have this property.
AREAS OF USE
Can be applied to concrete, wood, surfaces which are coated, painted or mosaic, brick, aerated concrete, OSB,
precast concrete panels, glass and EPS heat insulation panels.
APPLICATION
If there is mold or mossing on the surfaces, the fungicides should be exterminated.
If present, the peeling paint should be scraped off and the undamaged surface should be exposed.
Onto the cleaned surface, 150-200 grams of Isoweir Fixator should be applied per square meter.
Thermo application should begin after 1-2 hours, depending on the weather conditions.
While applying Isoweir Thermo coating, you should wait at least 2 hours between coats.
Achieving proper surfaces in short times is fundamental.
While jacketing, Styrofoam panels are adhered with Hemp Paint adhesive liquid.
Application of the coat is completed by putting on a net over it.
After waiting for an edequate time for it to dry, second coat is applied and the treatment is finished by applying
the desired color of Hemp Paint exterior paints
ADVANTAGE OF THE SYSTEM
It is not affected by cold or hot and it has a high bonding property.
Hemp Paint Thermal Insulation Plaster coating has heat insulating properties.
It does not create a thermal bridge in the jacketing.
It is light and it does not put a load on structures.
It is easy to apply.
STORAGE CONDITIONS
Store it in a sealed package which is not exposed to direct sunlight and between 5-35 °C degrees.
Keep the lid of the package closed when it is not used. Protect it from freezing.
READY TO USE. DO NOT ADD ANY WATER!
ACRYLIC ELASTIC SUFRACE COATING FOR 100% WATERPROOFING
PRODUCT DESCRIPTION
Elastic acrylic based exterior surface coating material, providing 100% water isolation on exterior surfaces of the building.
Offers a decorative appearance with a thick film layer formation on the surface. Elastic, light and strong with high
adherence. High U.V. endurance the
resistance to the chemical corrosion, fungus and bacterial
cracks on the surface. Overcomes the swelling problems of the surfaces. High
formations. Very strong adhesive properties on the surface.
Provides thermal isolation for heating cost reduction. This product contains hemp seed oil. It has antibacterial and anti
parazitic properties.
AREAS OF USE
On the surface of walls, wood and metal.
APPLICATION
For new construction : Horizontal and vertical areas needs to be applied with Hemp Paint Fixing Undercoat. Wait for at
least two hours then, apply two layers of Hemp Paint Elastic Exterior Facing. A brush or a roller can be used.
For old construction :Any old, loose and swelled paint layers on the surfaces must be removed. Cracks and splits on the
surface must be repaired. If there are fungus and mossy areas on the wall, fungus repellent needs to be applied before
Hemp Paint Fixing Undercoat. After waiting at least for two hours, apply two layers of Hemp Paint Elastic Exterior Facing.
A brush or a roller can be used.
DRYING TIME
Drying time of the Hemp Paint Elastic Exterior Coating can vary with temperature and air conditions. At 25 °C, there be
has to be a 30 minutes of waiting period between first and second layers. After the second layer is done. Drying time is
4 hours.
CONSUMPTION
For two layers of application, 1 m² of the surface can be covered with 0.6-0.9 kg of the product. On smooth surfaces
if there is a need for a thin film surface can be covered with 0,4 - 0,6 kg of the product.
READY TO USE. DO NOT ADD ANY WATER!
100% WATERPROOFING SOLUTION FOR WET SURFACES FROM FOUNDATION TO THE ROOF
PRODUCT DESCRIPTION
For wet surfaces,
Extarnal basement waterproofing,
Wet floors,
half - liquid resin based acrylic for 100 % water isolation, tixotropic, elastic, very high endurance to
half - liquid resin based acrylic for 100 % water isolation, tixotropic, elastic, very high endurance to extreme climate
conditions. Compiles with fire retardant coating standarts. When itis exposed to flame will be automaticly
extinguished. High resistant to U.V. rays. Even it strech two times more than its own legth, filming on the surface
will not suffer any cracks.
AREAS OF USE
Horizontal barriers
Crack and hose applications
Concrete treatments
Sealing of expansion joints
Bathroom and wet room waterproofing,
Floor coatings
Facade protection
Balcony and terrace waterpoofing,
Water tank and reservoir waterproofing,
Special waterproofing application,
Balcony and terrace waterpoofing,
APPLICATION
Surface must be free from dust, dirt, oil and it needs to be dry. Loose layers must be corrected if any
small splits and roughness on the surface can be corrected.
Before application, horizontal an d vertical surfaces must be undercoated with Hemp Paint Fixing Undercoating
thoroughly.
Felt applicati on must be certainly made in parapet corners, skylights, chimney bottoms, bridging splits,
pool applications, and horizontal and vertical concurrences. It is recommended that the surface exposed
to pedestrian and load traffic must be covered with a coating material such as aluminum or ceramic.
DRYING TIME
Tack dry: 2 hours
Complete drying: 24 hours
These values are given for 1 mm thickness at 20 C° temperature, the values can very with environmental conditions.
CANSUMPTION
0.75 – 1.5 kg per m² with double layer application.
READY TO USE. DO NOT ADD ANY WATER!
ACRYLIC BASE ELASTIC ROOF COATING PLASTER
PRODUCT DESCRIPTION
This unique product does not contain any kind of petrochemical compounds, bitummen, asphalt, rubber or
mineral stone like shingles. It is flexible roof isolation plaster. Hemp Paint Roof Insulation Plaster has a very
strong adherence on the surface and it can be used as the last layer on roofing systyms for insulation. It gives
100% water insulation and 15% thermal insulation. It’s not affected by head and cold.
It does not ignite spontaneously. If exposed to flame, it will put out automatically without spreading the
flame. Because of this feature, we can call this product a ‘Fire Retadant Coating’. It has special inorganic
pigmented colors that reflect the U.V. light.
AREAS OF USE
Can be used on all kind of concrete, wood, gas concrete, plasterboard, ceramic artical and natural stone.
OSB chipboards.
APPLICATION
Over woods, OSB (Oriented Strand Board), chipboard surfaces, you may apply two layers of the product by a
steel trowel and without using any Hemp Paint Fixing Undercoating.
Over metal, glass or PVC surfaces, apply first layer of Hemp Paint Fixing Undercoating, than apply two layer
of Hemp Paint Roof Plaster by steel trowel. According to the weather conditions, it must be left drying
minimum 2 hours for each layer. This product is water based, it dries when the water evaporate. Because of
that specialty, drying time is inversely correlated with the air temperature. If the temperature is high, drying time
becomes shorter. Do not apply below than 10°C. To clean the tools, use water and if any spots left, clean with
cellulosic thinner.
DRYING TIME
Applying at 20 °C, 2-3 mm thickness has 2 hours drying period.
Applying at 10 °C, 2-3 mm thickness has 4 hours drying period.
CONSUMPTION
Maximum 3 mm thickness consumption for 1 m2/two layers. 0,9 kg/L tixotropic (without fludity) solution .
READY TO USE. DO NOT ADD ANY WATER!
ACRYLIC BASE ELASTIC FOUNDATION ISOLATION PLASTER ASPHALT AND BITUMEN FREE
PRODUCT DESCRIPTION
for isolation and it provides 100% water
isolation and 15% thermal insulation. It’s not affected by heat and cold. It does not ignite spontaneously. If exposed to
flame, it will put out automatically without spreading the flame. Because of this feature, we can call this product ‘Fire
Retardant Coating’. It has special ingorganic pigmented color that reflect the U.V. lihgt.
AREAS OF USE
Concrete building foundations, outside basement walls
Maximum 3 mm thickness, consumption is 3 kg for each square metres in two layers.
Density 0.9 kg/L thixotropic ( with fluidity) solution.
with roller brush. According the weather conditions,
Apply Hemp Paint Fixing Undercoat on the surface first, then apply the first layer of Hemp Paint Construction Foundation
This unique product does not containany petrochemical comppounds, bitumen, asphalt, rubber or mineral stone
like shingles. It is a flexible foundation isolation plaster. Hemp Paint Construction Foundation Plaster has a very strong
adherence on the surface and it is used as the last layer on roofing systems
APPLICATION
there must be a waiting period at least 2 hours for each layer.
This product is water based, it dries when the water evaporate. Because of that specialty, drying time is the inversely
inversely correlated with air temperature. If the temperature is high, drying time becomes shorter. Do not apply below
10 °C. To clean the tools, use water and if any spots left, clean with cellulosic thinner.
DRYING TIME
Applying at 20°C, 2-3 mm thickness has a 2 hours drying period. Applying at 10°C, 2-3 mm thickness has a 4 hours
drying period.
CONSUMPTION
Maximum 3 mm thickness, consumption is 3 kg for each square metres in two layers. Density 0.9 kg/L thixotropic ( with fluidity) solution.
READY TO USE. DO NOT ADD ANY WATER!
STRONG HOLD ACRYLIC FIXATING PLASTER FOR ISOLATION MATERIALS
PRODUCT DESCRIPTION
An acrylic based fixating plaster with its unique air pocket structure provides very strong mounting-fixation
of many different items together. Such as bricks, woods, glaze, EPS-XPS etc. It is almost surface-free for mounting
items together. Perfectly use at exterior application. Elastic, light and strong with high adherence.
AREAS OF USE
Concrete and wooden surfaces
Plastered surfaces
Over brick and gas concrete
Painted surfaces
Over OSB and concrete surface
Glazed and mosaic etc. surfaces
Over EPS, XPS
APPLICATION
Any old, loose and swelled paint layers on the surfaces must be removed. Apply on the 4 corners of the application
surface with a steel trowel. The thickness of the application should not be more then 1.5 cm. and 1.5 kg. per m²
for fast drying and unnecessary consumption. Brush or roll can be use.
Drying time of the fixating plaster can vary with temperature air conditions. Maximum 24 hours.
With appliying the 4 corners of the surface, the 1m2 surface needs 0,75 kg fixating plaster .
DRYING TIME
CONSUMPTION
READY TO USE. DO NOT ADD ANY WATER!
EPOXY BASED 2K PRIMER
PRODUCT DESCRIPTION
Zeepas 2K solvent-free Epoxy is a resin-based, two-component primer which strongly adheres repair and bedding
mortars to new or old cured concrete surfaces.
AREAS OF APPLICATION
Because the material is solvent-free, it can safely be used in closed spaces, water tanks and areas where
accordance with food and hygiene provisions is desired.
Can be used to cover corroded ferro-concrete reinforcements.
It strengthens surface resistance on dilatation edges.
It is used before repair mortars as an adherence augmenter when repairing wide cracks on vertical and
horizontal surfaces of structures (Should be used with recommended aggregates.).
Can be used as a durable primer for repairs, patchhes and infillings.
Can be used to repair marine structures.
APPLICATION INSTRUCTIONS
S.a. 2.5 sand blasting should be applied on metal surfaces.
Concrete surfaces should be cleaned completely. Dust and loose particles should be removed with rotating
steel or vacuum cleaner.
When preparing the mixture, the ratio should be 75% Component A and 25% Component B by weight.
STORAGE CONDITIONS
Store it in a sealed package which is not exposed to direct sunlight and between 5-35 °C degrees. Keep the lid
of the package closed when it is not used. Protect it from freezing.
TWO COMPONENT SOLVENT FREE WATERBASE EPOXY PRODUCT DESCRIPTION
PRODUCT DESCRIPTION
Zeepson solvent-free epoxy is a resin-based, two-component topping material which is water and solvent resistant,
extremely durable against physical or chemical factors and provides hygiene.
AREAS OF APPLICATION
Because the material is solvent-free, it can safely be used in closed spaces, water tanks and areas where
accordance with food and hygiene provisions is desired (Can be used as a cladding or coating material in
drinking water tanks.). It is an antitoxin material. It does change the flavor or smell of water when used in the
water tanhs.
Can be used on swimming pools or other kinds of pools.
Can be used on facilities which produce food, hospitals and cool air tanks.
Can be used on storage tanks for petrol, fuel-oil, paran, oil, diesel fuel, various concentration, acid and
various solvents,
Can be used on cargo warehous
Can be used on closed garage floors,
es, ballast tanks, water tanks and other tanks.
APPLICATION INSTRUCTIONS
S.a. 2.5 sand blasting should be applied on metal surfaces.
Concrete surfaces should be cleaned completely. Dust and loose par ticles should be removed with rotating
steel or vacuum cleaner.
When preparing the mixture, the ratio should be 80% Component A and 20% Component B by weight.
Should not be thinned out. Epoxy Thinner should be used for tool cleaning.
STORAGE CONDITIONS
Store it in a sealed package which is not exposed to direct sunlight and between 5-35 °C degrees. Keep the lid
of the package closed when it is not used. Protect it from freezing.
U-POX FINISHING IS A TWO-COMPONENT
PRODUCT DESCRIPTION
U-POX finishing paint is a two-component, reaction grying nishg paint. Due its high ability to adhere in corrosive
environments and its high endurance to external factors it can be used successfully. It is recommended to be
applied after applying Zinc Phosphate Primer and base coat for metals and U-Pox Lak for concrete surfaces.
AREAS OF APPLICATION
Can be used on industrial facilities.
Can be used on steel constructions in constructions such as harbors, bridges and dams.
Can be used on acid, alkaline and solvent tanks with pipelines in chemical facilities.
Can be used on swimming pools and other kinds of pools.
RESISTANCE TO SUBSTANCES
Can endure gasoline, jet fuel, water with ammoniac, NaOH, KOH, NaCI, Sulphur dioxide, sea water, animal oils and
solutions with sugar for a long period of time.
Can endure acetone, alcohol, butyl acetate, tri-chlorine ethylene, toluol, H2SO4 (10%), HCL (10-50%), HNO3 (10%),
phosphoric acid, citric acid (10%), bromic acid (10%), acetic acid (10%) for a short period of time,
This product cannot endure benzol and butanol.
APPLICATION INSTRUCTIONS
Sa 2.5 sand blasting should be applied on metal surfaces.
Concrete surfaces should be cleaned completely. Dust and loose particles should be removed with rotating steel
or vacuum cleaner.
When preparing the mixture, the ratio should be 20 Kg Component A and 6 Kg Component B by weight.
Can be thinned out 10-20% with Epoxy Thinner depending on its mode of application.
STORAGE CONDITIONS
Store it in a sealed package which is not exposed to direct sunlight and between 5-35 °C degrees. Keep the lid
of the package closed when it is not used. Protect it from freezing.
ZINC PHOSPHATE EPOXY PRIMER
PRODUCT DESCRIPTION
Zinc Phosphate Epoxy Primer is a epoxy-based, two-component primer paint with high adhesive qualities.
It has high corrosion endurance because it contains zinc phosphate. It adheres perfectly on iron sheets and
steel surfaces as well as aluminum and galvanize surfaces. It is preferable priming system in terms of pollution
because it does not contain lead and zinc chromate.
AREAS OF APPLICATION
It can be used in food warehouses because it is not toxic.
Can be used successfully on any metal surfaces in car manufacturing and sub-industry, mainly the production
of commercial vehicles and rooftop equipment
Can be used as a double layer primer or a base layer on steel structures which require high corrosion endurance.
Can be used as the first layer primer for protect metal surfaces of industrial facilities and sea vehicles which are
always exposed to wetand muddy environments.
APPLICATION INSTRUCTIONS
S.a. 2.5 sand blasting should be applied. Blasted surface should be cleaned with dry air.
The surface should be stripped of oil, dirt or other materials that might prevent the primer from adhering with
chemicals.
Primer should be applied on metal surfaces before the oxidation starts,
When preparing the mixture, the ratio should be 20 Kg Component A and 6 Kg Component B by weight.
Can be thinned out 10-15% with Epoxy Thinner depending on its mode of application.
In closed speces where application is taking place the area should be aerated sufficiently. In addition due to the
solvents it contains. The meterial should not be in the same place with tools and operations which require
electricity or fire
STORAGE CONDITIONS
Store it in a sealed package which is not exposed to direct sunlight and between 5-35 °C degrees. Keep the lid of
the package closed when it is not used. Protect it from freezing.
WATER INSULATOR FOR TRANSPARENT FLOOR MATERIALS
PRODUCT DESCRIPTION
A single component transparent waterproofing material for surface such as faience, ceramic etc. Used for water
proofing on surfaces such as glazed tile/ceramic, marble, granite and glass. Once it is dry, it forms a transparent,
elastic and jointless layer. After the application, it shows high crack-bridging property. It is not affected by UV
rays and external weather conditions. It does not turn yellow, wilt or buckle over time. It is resistant to abrasion
and various chemicals. Additionnally it is not affected by human or vehicle traffic. It is easily applied without
damaging the coating especially in insulation problems occurring on the floors of balconies, terraces and bathrooms.
In addition, it can be applied on glass brick, wood, polycarbonate sheets and PVC based surfaces. Its adherence is
excellent.
AREAS OF USE
In concretes, plasters and alums,
In faience, ceramic, marble, granite, cotta and naturel stone,
In travertine and pressed bricks,
In glass, glass brick, mosaic and mosaic tile,
On PVC, aluminum, wood, GRP, polycarbonate sheets,
On stone covered exteriors of balcony, terrace, bathroom, kitchen.
APPLICATION
The application surface must be dry and clean. The application cannot be made on moist or wet surfaces. It is not
applied on surfaces affected with salt eflorescence, water vopar pressure and water from negative side. The oiled
dirty surface must be cleaned with solbent based cleaners. If the joints on the application surface are damaged,
they must be renewed. The applications are done with a brush or a roller. On joint surfaces, the application is applied
on joints at first, then applied on the whole surface in two layers. A thorough drying muts be provided layers.
The freshly applied surface must be protected from dust, water and rain until a thorough drying has been achieved.
CONSUMPTION
100-200 ml / m²
READY TO USE. DO NOT ADD ANY WATER!